[CPMD-list] JOB LIMIT

[Ari P Seitsonen]

Dear Sergei,

  From this it's very difficult even to guess the possible reason of the 
problem. Could you pleaes provide us with the whole input and output files 
and information on your compiler and operating system? I cannot promise 
that we can help with that, however it might lead us to the problem.

    Greetings from the foggy Zurich,

       apsi

-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-=*=-
 Ari Paavo Seitsonen / Ari.P.Seitsonen at iki.fi / http://www.iki.fi/~apsi/
 Tel +41 1 635 44 97 / Fax +41 1 635 68 38 / GSM +41 79 719 09 35      
 Anschrift: Physikalisch Chemisches Institut (PCI), Universität Zürich (UniZh)
 Indirizzo: Winterthurerstraße 190, CH-8057 Zürich
 Address:   Schweiz / Svizzera / Suisse / Svizra / Switzerland

On Sat, 6 Dec 2003, Sergei Lisenkov wrote:

> Dear CPMD users,
> I see that my calculations was done. But in output file I have met the next:
> ....
>  279 0.002866 0.000021    -340.98527     -0.000001     55.07
>  280 0.002865 0.000021    -340.98527     -0.000001     55.44
>  281 0.002864 0.000021    -340.98527     -0.000001     41.30
>  282 0.002862 0.000021    -340.98527     -0.000001     54.69
>  283 0.002861 0.000021    -340.98527     -0.000001     53.67
>  284 0.002860 0.000021    -340.98527     -0.000001     51.83
>  285 0.002858 0.000021    -340.98527     -0.000001     52.56
>  ****************************************************************
>  *                                                              *
>  *            JOB LIMIT TIME EXCEEDED FOR A NEW LOOP            *
>  *                                                              *
>  ****************************************************************
>  * THE JOB TIME LIMIT IS:                         0.000 SECONDS *
>  * THE TIME OF THE LAST LOOP IS:          ************* SECONDS *
>  * THE REMAINING JOB TIME IS:             ************* SECONDS *
>  *      THE COMMAND WAS ISSUED AT Fri Dec  5 19:01:18 2003      *
>  *                                                              *
>  ****************************************************************
>  ****************************************************************
>  *                                                              *
>  *            JOB LIMIT TIME EXCEEDED FOR A NEW LOOP            *
>  *                                                              *
>  ****************************************************************
>  * THE JOB TIME LIMIT IS:                         0.000 SECONDS *
>  * THE TIME OF THE LAST LOOP IS:          ************* SECONDS *
>  * THE REMAINING JOB TIME IS:             ************* SECONDS *
>  *      THE COMMAND WAS ISSUED AT Fri Dec  5 19:01:19 2003      *
>  *                                                              *
>  ****************************************************************
>  ================================================================
>  =              END OF GEOMETRY OPTIMIZATION                    =
>  ================================================================
> 
> 
> 
>  RESTART INFORMATION WRITTEN ON FILE                  ./RESTART.1
> 
>  ****************************************************************
>  *                                                              *
>  *                        FINAL RESULTS                         *
>  *                                                              *
>  ****************************************************************
> 
> But in input file I have no limit for job work. Why it finished?
> 
> Thanks,
> Sergey
> _______________________________________________
> CPMD-list mailing list
> CPMD-list at cpmd.org
> http://www.cpmd.org/mailman/listinfo/cpmd-list
>